PDA

View Full Version : Homemade Slice



jdels
06-25-2020, 05:41 PM
Picked up some 50mm Variegated Go Getter mines on a whim. Set up is going well so did a 'special' project today. Plan is to hit them all at once in front of a Dominator Instant Crackle. Couple hours work for a 3 second hit Should be worth it!

http://www.pyrotalk.com/bulletin/attachment.php?attachmentid=5059&stc=1
http://www.pyrotalk.com/bulletin/attachment.php?attachmentid=5060&stc=1
http://www.pyrotalk.com/bulletin/attachment.php?attachmentid=5061&stc=1
http://www.pyrotalk.com/bulletin/attachment.php?attachmentid=5062&stc=1
http://www.pyrotalk.com/bulletin/attachment.php?attachmentid=5063&stc=1

Robbro097
06-25-2020, 06:20 PM
I hppe you get video of that. I love those go getter mines, and the instant crackle rocks

krayg
06-26-2020, 11:03 AM
I like it.

PyroGyro
06-27-2020, 11:01 AM
please get a video and post it. I do wonder if there's enough angles there but nice job!

jdels
06-27-2020, 10:54 PM
please get a video and post it. I do wonder if there's enough angles there but nice job!

Overall arc ended up at about 85 degrees. Looking to fill in front of an instant crackle.

jdels
06-27-2020, 11:01 PM
Wired up and in her prom dress.

http://www.pyrotalk.com/bulletin/attachment.php?attachmentid=5076&stc=1

jamisonlm3
06-27-2020, 11:16 PM
You seem to want to really make sure those don't go off by accident.

jdels
06-27-2020, 11:20 PM
You seem to want to really make sure those don't go off by accident.

Tight set up and its part of finale.

Rick_In_Tampa
06-28-2020, 06:19 AM
Great work!! Looking forward to seeing the video.

PyroGyro
07-08-2020, 05:40 PM
Where's the vid?

AquaticPyro
07-10-2020, 05:53 AM
Yeah, I would do it the lazy way like when you do roman candle racks by using screws to separate rather then cutting and gluing all those wood dividers. However I might use that method for building one of my HDPE racks. I hope you also attach a 2x4 across the bottom so it does not tip over like with a rack.

jdels
07-10-2020, 04:27 PM
Where's the vid?

Show not edited yet but here it is. Video angle not great. Comes in at about the 28 second mark.


https://youtu.be/Xql8xxxYyQM

jdels
07-10-2020, 04:30 PM
Yeah, I would do it the lazy way like when you do roman candle racks by using screws to separate rather then cutting and gluing all those wood dividers. However I might use that method for building one of my HDPE racks. I hope you also attach a 2x4 across the bottom so it does not tip over like with a rack.

It was screwed down to one of my frames. With any luck I'm going to break the key joints loose and reload for next year (or sooner).

PyroGyro
07-10-2020, 05:18 PM
Show not edited yet but here it is. Video angle not great. Comes in at about the 28 second mark.


https://youtu.be/Xql8xxxYyQM

Unfortunately can't see it well from that angle but it did get a good reaction from the crowd so it must've been nice!

Robbro097
07-10-2020, 08:00 PM
Thanks for sharing def got a pop from the audience. I love go getters